Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.5

ISSN Печать: 2152-5102
ISSN Онлайн: 2152-5110

Выпуски:
Том 46, 2019 Том 45, 2018 Том 44, 2017 Том 43, 2016 Том 42, 2015 Том 41, 2014 Том 40, 2013 Том 39, 2012 Том 38, 2011 Том 37, 2010 Том 36, 2009 Том 35, 2008 Том 34, 2007 Том 33, 2006 Том 32, 2005 Том 31, 2004 Том 30, 2003 Том 29, 2002 Том 28, 2001 Том 27, 2000 Том 26, 1999 Том 25, 1998 Том 24, 1997 Том 23, 1996 Том 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v24.i4-6.50
pages 488-497

Initial Atomization of an Intermittent Spray from a Diesel Nozzle

Hideo Takahashi
Department of Mechanical Engineering, Gunma College of Technology, Gunma, Japan
M. Kono
Department of Aeronautics & Astronautics, University of Tokyo, Tokyo, Japan
Hiroki Yanagisawa
Mitsubishi Motor Corporation
Siichi Shiga
Department of Mechanical Engineering, Faculty of Engineering, Gunma University, Gunma, Japan
Takao Karasawa
Department of Mechanical Engineering, Faculty of Engineering, Gunma University, Gunma, Japan
Hisao Nakamura
Department of Mechanical Engineering, Faculty of Engineering, Gunma University, Gunma, Japan

Краткое описание

The purpose of this study is to clarify the atomization mechanisms of an intermittent fuel spray in its very early stage of injection. A single hole diesel nozzle was used in rather wide range of valve opening pressure from 5 to 70 MPa. The measurement of injection pressure inside the nozzle-sac, that is just at the upstream of the orifice, was attempted by using a micro-strain gauge. Two observation apparatuses were used, an image-converting high-speed camera with the framing rate of 105 f.p.s. and an image-intensified CCD camera with high-speed gating. At the very beginning of injection, an emergence of a liquid column was observed, which had almost the same diameter as the orifice. Then the liquid column spread radially, forming a spray angle in the vicinity of the nozzle exit. The timing of the spray angle formation was shown to become earlier with increasing the in valve opening pressure. Furthermore the pressure inside the nozzle-sac at this moment did not vary. This pressure approximately corresponds to that of the transition from a wavy jet to a developed spray in the atomization regime for a steady jet. Thus, it is suggested that the atomization mechanism of a steady jet could be applicable to the unsteady spray formation process. Under several injection conditions, it was observed the formation of a thin thread at the tip of the original spray. It appeared at the very beginning of injection, and developed to the length of 2 or 3 mm. The tip gradually broke up, decreased the velocity, and was finally caught up by the original spray.


Articles with similar content:

DIESEL SPRAY IMPINGING ON A FLAT WALL. PART II: VOLUME AND AVERAGE AIR-FUEL RATIO OF AN IMPINGEMENT DIESEL SPRAY
Atomization and Sprays, Vol.12, 2002, issue 5&6
Masataka Arai, Kyungnam Ko
TOMOGRAPHIC VISUALIZATION OF THE DENSE CORE REGION IN TRANSIENT DIESEL SPRAYS
ICLASS 94
Proceedings of the Sixth International Conference on Liquid Atomization and Spray Systems, Vol.0, 1994, issue
Gregory J. Smallwood, David R. Snelling, Omer L. Gulder
EXPERIMENTAL STUDY ON VELOCITY DISTRIBUTION OF POSTIMPINGEMENT DIESEL SPRAY ON A WALL. PART 1: EFFECT OF IMPINGEMENT ANGLE ON FLOW PATTERN
Atomization and Sprays, Vol.24, 2014, issue 8
Masataka Arai, Yoshio Zama, Tomohiko Furuhata, Mohd Zaid Akop, Kazuma Sugawara
FOAM FLOW OF OIL-REFRIGERANT R134a MIXTURE IN A SMALL DIAMETER TUBE
International Heat Transfer Conference 13, Vol.0, 2006, issue
José Luiz Gasche, Heryca Olenir Sousa Castro
Image Analysis of a Diesel Spray Impinging on a Wall
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Masataka Arai, T. Ebara, Kenji Amagai