Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.737 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 30, 2020 Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v13.i23.40
20 pages

EXPERIMENTAL INVESTIGATIONS OF SPRAY/WALL IMPINGEMENT

W. S. Mathews
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois, USA
C. F. Lee
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois, USA
James E. Peters
Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois, USA

Краткое описание

A complete set of spray impingement data, including incoming and secondary droplet size and velocity, spray visualization images, and deposited film shape and thickness, are presented. A pintle injector was used for all measurements, and the fuel used was iso-octane. The fuel impinged upon a flat Plexiglas plate, with an average surface roughness of 40 Е. Three separate impingement angles were considered: 30°, 45°, and 60° from normal. A phase Doppler particle analyzer (PDPA) was used to characterize the incoming fuel spray as well as the secondary droplet cloud. An unintensified CCD camera was used to take images of the fuel film formation and the evolution of the secondary droplet cloud. Finally, an optical, nonintrusive technique was used to determine the thickness of the deposited fuel film. Calibration of the optical technique was performed, and good agreement was shown over the entire range of film thickness. This set of data provides detailed information necessary for verifying spray impingement and film deposition and evolution models.


Articles with similar content:

BREAKUP AND ATOMIZATION OF A KEROSENE JET IN CROSSFLOWAT ELEVATED PRESSURE
Atomization and Sprays, Vol.12, 2002, issue 1-3
Christoph Hassa, Julian Becker
COMBINED FOCUSED SHADOW AND COMPUTERIZED TOMOGRAPHIC ANALYSIS OF A SPRAY IMPINGING ON A FLAT END OF A ROUND STICK
ICHMT DIGITAL LIBRARY ONLINE, Vol.18, 1992, issue
Keiya Nishida, Mamoru Suzuki, Hiroyuki Hiroyasu
IMPINGEMENT OF HIGH-PRESSURE GASOLINE SPRAYS ON ANGLED SURFACES
Atomization and Sprays, Vol.16, 2006, issue 6
Jim H. Whitelaw, J. M. Nouri
A COMPARISON OF SPRAY ANGLE MEASUREMENTS USING OPTICAL AND MECHANICAL METHODS
Atomization and Sprays, Vol.20, 2010, issue 1
Roger Seei, Yudaya R. Sivathanu, Jongmook Lim, Bill Wallace
VISUALIZATION OF INTERACTING PILOT AND MAIN DIESEL-TYPE SPRAYS IN AN ENGINE
Journal of Flow Visualization and Image Processing, Vol.2, 1995, issue 1
D. Pushka, B. Chehroudi, K. M. Sinko