Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Atomization and Sprays
Импакт фактор: 1.737 5-летний Импакт фактор: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Печать: 1044-5110
ISSN Онлайн: 1936-2684

Выпуски:
Том 30, 2020 Том 29, 2019 Том 28, 2018 Том 27, 2017 Том 26, 2016 Том 25, 2015 Том 24, 2014 Том 23, 2013 Том 22, 2012 Том 21, 2011 Том 20, 2010 Том 19, 2009 Том 18, 2008 Том 17, 2007 Том 16, 2006 Том 15, 2005 Том 14, 2004 Том 13, 2003 Том 12, 2002 Том 11, 2001 Том 10, 2000 Том 9, 1999 Том 8, 1998 Том 7, 1997 Том 6, 1996 Том 5, 1995 Том 4, 1994 Том 3, 1993 Том 2, 1992 Том 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v13.i23.90
11 pages

ON QUANTIFYING INTERFACIAL THERMAL RESISTANCE AND SURFACE ENERGY DURING MOLTEN MICRODROPLET SURFACE DEPOSITION

D. Attinger
Department of Mechanical Engineering, State University of New York at Stony Brook, Stony Brook, New York, USA
Dimos Poulikakos
Laboratory of Thermodynamics in Emerging Technologies, Institute of Energy Technology Mechanical and Process Engineering Department, ETH Zurich, Switzerland

Краткое описание

Understanding and controlling the deposition of a molten microdroplet on a colder substrate with simultaneous heat transfer and solidification is of central importance to a host of technologies, exemplified by novel methods of electronic microchip manufacturing. The physics of the interfaciat phenomena involved are to date only partially understood. For instance, the transient resistance to heat transfer at the droplet—substrate interface cannot be quantified theoretically, and adequate experimental data are lacking. Serious obstacles to experimental determination are the very short time and length scales involved (of the order of micrometers: and microseconds). In the present article, a numerical modeling for droplet impact and solidification based on the Navier-Stokes and energy equations is used in order to reproduce transient measurements of the deposition of a eutectic Pb-Sn microdroplet on a multilayer wafer. The resistance to heal transfer at the droplet—wafer interface and the surface energy of the molten microdroplet are determined by matching numerical and experimental results. This successfully demonstrated indirect method is of interest if direct transient thermal resistance data are not available (as is very often the case).


Articles with similar content:

COMBINED EXPERIMENTAL AND NUMERICAL SIMULATION OF CONVECTIVE TRANSPORT
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2014, issue
Yogesh Jaluria
HYDRODYNAMIC AND KINETIC MODELS OF DROPLET HEATING AND EVAPORATION: ANALYSIS AND APPLICATIONS
ICHMT DIGITAL LIBRARY ONLINE, Vol.13, 2008, issue
Morgan R. Heikal, Sergey Martynov, Sergei S. Sazhin, Irina N. Shishkova
HEAT TRANSFER PHENOMENA DURING CONTINUOUS CASTING OF ALUMINIUM ALLOYS
International Heat Transfer Conference 10, Vol.1, 1994, issue
L. Katgerman
A Non-Intrusive Inverse Problem Technique for the Identification of Contact Failures in Double-Layered Composites
International Heat Transfer Conference 15, Vol.24, 2014, issue
Luiz A.S. Abreu, HELCIO ORLANDE, Carlos J.S. Alves, Marcelo Jose Colaco
NUMERICAL SIMULATION OF THE EFFECT OF CONTACT ANGLE ON THE THERMAL RESPONSE OF THE SOLID DURING NUCLEATE POOL BOILING
Interfacial Phenomena and Heat Transfer, Vol.2, 2014, issue 4
Eduardo Aktinol, Vijay K. Dhir