Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
SJR: 0.176 SNIP: 0.48 CiteScore™: 1.3

ISSN Печать: 1093-3611
ISSN Онлайн: 1940-4360

Выпуски:
Том 24, 2020 Том 23, 2019 Том 22, 2018 Том 21, 2017 Том 20, 2016 Том 19, 2015 Том 18, 2014 Том 17, 2013 Том 16, 2012 Том 15, 2011 Том 14, 2010 Том 13, 2009 Том 12, 2008 Том 11, 2007 Том 10, 2006 Том 9, 2005 Том 8, 2004 Том 7, 2003 Том 6, 2002 Том 5, 2001 Том 4, 2000 Том 3, 1999 Том 2, 1998 Том 1, 1997

High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes

DOI: 10.1615/HighTempMatProc.v2.i3.50
pages 359-367

X-RAY DETERMINATION OF RESIDUAL STRESSES AND PHASE QUANTIFICATION IN Zr02 OXIDE LAYERS FORMED ON ZIRCALOY-4

J.L Bechade
CEREM/DECM/SRMA CEA-SACLAY - 91191 Gif sur Yvette Cedex - France
M. Gailhanou
Lab. de Metallurgie Physique - Universite de Poitiers - 86960 Futuroscope - France (°) LURE - Universite Paris-Sud - 91405 Orsay Cedex - France
P. Goudeau
CEREM/DECM/SRMA CEA-SACLAY - 91191 Gif sur Yvette Cedex - France
P. Yvon
CEREM/DECM/SRMA CEA-SACLAY - 91191 Gif sur Yvette Cedex - France

Краткое описание

The residual stress state and the microstructure of Zr02 oxide layers formed on Zircaloy-4 plates in steam at 400°C were studied using x-ray diffraction techniques.
One of the most important features of the corrosion mechanism of Zircaloy is the development of compressive stresses within the oxide which strongly affect the microstructure of the growing oxide and the diffusion of oxidizing species. These compressive stresses can also favor the formation of tetragonal zirconia over monoclinic zirconia. Therefore, the accurate determination of the stress state and the composition of the oxide is essential for the understanding of the corrosion mechanism and the modelling of its kinetics.
The samples were prepared by oxidation of Zy-4 plates in an autoclave at 400°C in a vapor pressure of 10.3 MPa. Using conventional x-ray diffraction, it can be shown that the amount of tetragonal zirconia in the oxide layer decreases continuously with the oxidation time, however, with this type of radiation it is very difficult to obtain the phase distribution and the stress level profile in the oxide layer.
To obtain more accurate information, specific diffractometers on the French synchrotron radiation facility (LURE Orsay) were used to work at higher wavelengths. The following experimental results were obtained :
- High compressive stresses were found in the oxide layer and a strong effect of the oxide texture was observed.
- There seems to be a trend for the tetragonal zirconia to be preferentially located at the interface metal/oxide.


Articles with similar content:

INFLUENCE OF SUBSTRATE COMPOSITION, OXIDE SCALE MORPHOLOGY AND OTHER PHYSICAL PARAMETERS ON THE RESIDUAL STRESSES IN ALUMINA SCALES DEVELOPED AT HIGH TEMPERATURE ON FeCrAl ALLOYS
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.2, 1998, issue 3
J.L. Lebrun, K. Messaoudi, A.M. Huntz , B. Lesage
THE USE OF MOLYBDENUM ACTIVATOR FOR DEPOSITION OF FLUOROPOLYMER COATINGS WITH DIFFERENT STRUCTURES BY THE HOT WIRE CHEMICAL VAPOR DEPOSITION METHOD
Interfacial Phenomena and Heat Transfer, Vol.7, 2019, issue 2
Alexey I. Safonov, Nikolay I. Timoshenko, Denis Y. Panin
STRUCTURAL AND PHYSICAL PROPERTIES OF Al–X wt.% (α-Fe2O3) METAL MATRIX COMPOSITE
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.22, 2018, issue 4
Mohamed Yacine Debili, A. Boutouta
INFLUENCE OF PREHEATING PARAMETERS ON THE PLASMA-JET OXIDATION OF A LOW-CARBON STEEL
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.15, 2011, issue 1
B. Hannoyer, J. Pech, Alain Denoirjean, O. Lagnoux, Pierre Fauchais
AN/AD/Mg IGNITION BY CO2 LASER RADIATION
International Journal of Energetic Materials and Chemical Propulsion, Vol.5, 2002, issue 1-6
V. Tadi, S. Peila, B. N. Kondrikov