Доступ предоставлен для: Guest
Портал Begell Электронная Бибилиотека e-Книги Журналы Справочники и Сборники статей Коллекции
Journal of Flow Visualization and Image Processing
SJR: 0.161 SNIP: 0.312 CiteScore™: 0.5

ISSN Печать: 1065-3090
ISSN Онлайн: 1940-4336

Выпуски:
Том 27, 2020 Том 26, 2019 Том 25, 2018 Том 24, 2017 Том 23, 2016 Том 22, 2015 Том 21, 2014 Том 20, 2013 Том 19, 2012 Том 18, 2011 Том 17, 2010 Том 16, 2009 Том 15, 2008 Том 14, 2007 Том 13, 2006 Том 12, 2005 Том 11, 2004 Том 10, 2003 Том 9, 2002 Том 8, 2001 Том 7, 2000 Том 6, 1999 Том 5, 1998 Том 4, 1997 Том 3, 1996 Том 2, 1995 Том 1, 1993

Journal of Flow Visualization and Image Processing

DOI: 10.1615/JFlowVisImageProc.2016016100
pages 117-129

THE GROWTH CHARACTERISTICS OF TRANSIENT IMPINGING AXISYMMETRIC TURBULENT JETS

Brian D. Landers
Department of Aerospace Engineering, University of Cincinnati, Cincinnati, OH, USA 45221-0070
Peter J. Disimile
Department of Aerospace Engineering, University of Cincinnati, Cincinnati, OH, USA 45221-0070

Краткое описание

This paper presents a study performed to evaluate the growth characteristics of transient impinging axisymmetric turbulent jets at a Reynolds number of 7500 for three different impingement angles (30, 45, and 60 deg). Previous studies have been performed on a single transient turbulent jet as well as steady-state turbulent impinging jets. However, in the case of internal and diesel combustion engines, mixing of the fuel and oxidizer occurs under a transient condition just prior to ignition. This mixing application results from the impingement of these two fluid streams. Therefore, the current study utilizes smoke visualization to characterize the vertical and horizontal mixing layer widths of two identical turbulent air jets impinging at three different angles; as well as the time it takes for the mixture to travel downstream from the jets origin. The current results show an increase in the mixing layer width by approximately 3 diameters near the impingement point in both the vertical and horizontal directions when the transient case is compared to the steady-state cases. Also, by increasing the impingement point from 30 to 60 deg the maximum growth in both the horizontal and vertical directions is increased by approximately 30% (i.e., 1 diameter). Finally, by increasing the impingement angle from 30 to 60 deg the time it takes for the mixture to travel downstream from the jet origin to x/D = 15 increases by more than a factor of two.


Articles with similar content:

OPTICAL ANALYSIS OF THE MIXING EFFECT IN FULLY DEVELOPED LIKE-DOUBLET IMPINGING JET SPRAYS
Atomization and Sprays, Vol.22, 2012, issue 5
Berlin Huang, Tony Yuan
Heat transfer and flow field measurements of a pulsating round jet impinging on a flat heated surface
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2018, issue
Gershon Grossman, V. Rinsky, Motti Raizner, R. van Hout
Image Analysis of a Diesel Spray Impinging on a Wall
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Masataka Arai, T. Ebara, Kenji Amagai
HEAT TRANSFER FROM A DISCRETE HEAT SOURCE IN CONFINED AIR JET IMPINGEMENT
International Heat Transfer Conference 11, Vol.14, 1998, issue
Suresh V. Garimella, Vincent P. Schroeder
Heat Transfer and Flow Characteristics of Impinging Jet with Triangular Multi-tabs
International Heat Transfer Conference 13, Vol.0, 2006, issue
Y. G. Jang, K. J. Lee, S. J. Lee