Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.5

ISSN Imprimir: 2152-5102
ISSN On-line: 2152-5110

Volumes:
Volume 46, 2019 Volume 45, 2018 Volume 44, 2017 Volume 43, 2016 Volume 42, 2015 Volume 41, 2014 Volume 40, 2013 Volume 39, 2012 Volume 38, 2011 Volume 37, 2010 Volume 36, 2009 Volume 35, 2008 Volume 34, 2007 Volume 33, 2006 Volume 32, 2005 Volume 31, 2004 Volume 30, 2003 Volume 29, 2002 Volume 28, 2001 Volume 27, 2000 Volume 26, 1999 Volume 25, 1998 Volume 24, 1997 Volume 23, 1996 Volume 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v38.i2.30
pages 122-143

Control of Separation Flow in Sudden Enlargement

A. Abdel-Fattah
Department of Mechanical Power Engineering, Faculty of Engineering Menoufiya University, Shebin El-Kom

RESUMO

In the present paper, an injection flow in separation zone in sudden enlargement has been studied experimentally and numerically. The injected flow is achieved through twelve slots placed around the inner side wall of the step. The static pressure is measured and calculated along the wall of sudden enlargement for different values of injection ratio and injection flow angles. The average heat transfer variation with injection Reynolds number (Rej) has been obtained for different values of the injection flow angle. The mean velocity vector, velocity contours, turbulent kinetic energy contours and temperature contours are found. The flow Reynolds number of injected flow in this study is found to vary between 320 and 840, the flow Reynolds number for the main flow is 5895 to 8450 at injection flow angles of 0, 15, 30, 45 and 60°. The results indicate that, the pressure recovery coefficient increases by decreasing the injection ratio and increasing the injection flow angle. The average heat transfer coefficient increases as both injection Reynolds number and injection flow angle increase. The numerical results show that two recirculation zones generate behind the step between the injected flow and the main flow. The size of these recirculation zones decreases by increasing the injection flow rate. The turbulent kinetic energy increases within the region between the recirculation zone and main zone. On the contrary, it decays by injecting flow in the recirculation zone. The zone for higher value of flow temperature decreases by injecting flow in the recirculation zone, and this zone increases as the injection flow rate increases. The comparison between the experimental and the numerical results using the k-ε model with Leschziner and Rodi correction show a fairly good agreement.


Articles with similar content:

Effect of Inlet Flow Angle on the Flow Characteristics in Chamber
International Journal of Fluid Mechanics Research, Vol.38, 2011, issue 1
A. Abdel-Fattah
PREDICTION OF FLOW AND HEAT TRANSFER INSIDE A TWO-PASS ROTATING CHANNEL WITH ANGLED RIBBED SURFACES
Journal of Enhanced Heat Transfer, Vol.23, 2016, issue 2
Aminallah Miloud, Berrabah Brahim
Forced convection
NUMERICAL SIMULATION OF TRANSIENT COOLING EFFECT WITH WALL MASS INJECTION BEHIND THE BACKSTEP

ICHMT DIGITAL LIBRARY ONLINE, Vol.11, 2004, issue
Yue-Tzu Yang, Kuo-Teng Tsai
Numerical Investigation of Flow and Heat Transfer around Two Semi-Circular Cylinders with a Splitter Plate
Heat Transfer Research, Vol.42, 2011, issue 7
Hadi Heidary, Mostafa Nourollahi, Kurosh Sedighi, Mousa Farhadi
EXPERIMENTAL AND NUMERICAL INVESTIGATION OF NOISE GENERATION BY TURBULENT COMBUSTION IN A COMBUSTOR
TSFP DIGITAL LIBRARY ONLINE, Vol.3, 2003, issue
M. Dusing, Johannes Janicka, S. Kartheekeyan, Satyanarayanan R. Chakravarthy, Amsini Sadiki, R. I. Sujith