Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.5

ISSN Imprimir: 2152-5102
ISSN On-line: 2152-5110

Volumes:
Volume 46, 2019 Volume 45, 2018 Volume 44, 2017 Volume 43, 2016 Volume 42, 2015 Volume 41, 2014 Volume 40, 2013 Volume 39, 2012 Volume 38, 2011 Volume 37, 2010 Volume 36, 2009 Volume 35, 2008 Volume 34, 2007 Volume 33, 2006 Volume 32, 2005 Volume 31, 2004 Volume 30, 2003 Volume 29, 2002 Volume 28, 2001 Volume 27, 2000 Volume 26, 1999 Volume 25, 1998 Volume 24, 1997 Volume 23, 1996 Volume 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v25.i4-6.340
pages 822-832

Enhancement of Convective Heat Transfer with Phase-Change Particles

Eunsoo Choi
Department of Mechanical Engineering and Mechanics, Drexel University, Philadelphia, PA 19104, USA
Harold G. Lorsch
Department of Mechanical Engineering and Mechanics, Drexel University, Philadelphia, PA 19104, USA

RESUMO

A new method using a phase-change-material slurry to enhance convective heat transfer was studied in this research. Hexadecane was used as a phase-change material and was mixed with water, the carder fluid. An emulsifier was used to generate fine and homogeneous hexadecane particles in water. The hexadecane-water slurry was circulated through a heating test section, where pressure drops and heat transfer coefficients were measured. The heating test section was made of 6.532 m long, 10.14 mm ID stainless steel tubing and heated by a high current DC power supply, resulting in a uniform heat flux boundary condition.
The solid particles used in the present study were small enough to prevent clogging. The local pressure drop was found to decrease when the solid particles melted, a phenomenon which was used to find out the location of the slurry melting. The behavior of local heat transfer coefficient curve was quite distinctive in three region along the heating test section. In the first region, the heat transfer coefficient increased along the test section because the number of the melted particles on the wall increased. In the second region, it decreased because the number of solid particles abruptly decreased. In the third region, it increased because of the temperature-dependent viscosity effect. The maximum local heat transfer coefficient was about twice as high as that without phase-change materials.


Articles with similar content:

ENHANCEMENT OF CONVECTIVE HEAT TRANSFER WITH PHASE-CHANGE PARTICLES
Transport Phenomena in Thermal Engineering. Volume 2, Vol.0, 1993, issue
Eunsoo Choi, Young I. Cho, Harold G. Lorsch
EXPERIMENTAL AND NUMERICAL STUDY OF HEAT TRANSFER ENHANCEMENT IN A PIPE PARTIALLY OR TOTALLY FILLED WITH A POROUS MATERIAL
3rd Thermal and Fluids Engineering Conference (TFEC), Vol.26, 2018, issue
Saeed Tiari, Ali Heidari, Majid Saffar Avval, Mahboobe Mahdavi
EFFECTS OF SCALING ON PRESSURE DROP AND TUBE WALL TEMPERATURE OF STEAM INJECTION BOILERS REUSING OIL FIELD PRODUCED WATER
Heat Transfer Research, Vol.50, 2019, issue 2
Liang Gong, Wei Zhang, Bin Li
PORE-SCALE SIMULATION OF ICE MELTING PROCESS IN POROUS MEDIA
Second Thermal and Fluids Engineering Conference, Vol.32, 2017, issue
Li Chen, Yu-Tong Mu, Pu He, Wen-Quan Tao
EXPERIMENTAL STUDY ON FLOW AND HEAT TRANSFER IN POROUS MEDIA
3rd Thermal and Fluids Engineering Conference (TFEC), Vol.17, 2018, issue
Ping Wang, Zhang Zhang, Yihan Luo , Jinpeng LV , Xingwang Tian, Bingchen Yu , Shengqiang Shen