Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Atomization and Sprays
Fator do impacto: 1.737 FI de cinco anos: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Imprimir: 1044-5110
ISSN On-line: 1936-2684

Volumes:
Volume 30, 2020 Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v20.i3.30
pages 211-225

EFFECT OF BUBBLE GENERATION CHARACTERISTICS ON EFFERVESCENT ATOMIZATION AT LOW GAS-LIQUID RATIO OPERATION

Sina Ghaemi
Payam Rahimi
Department of Mechanical Engineering, University of Alberta, Edmonton, Alberta T6G 2G8, CANADA
David S. Nobes
University of Alberta, Department of Mechanical Engineering, Edmonton, T6G 2G8, Alberta, Canada

RESUMO

An experimental investigation into the performance of an effervescent atomizer operated with two different styles of air injectors during low gas-liquid ratio (GLR) operation is discussed. A typical multihole air supply tube and an injector that utilizes a porous media for gas injection are investigated. A preliminary study visualized the two-phase flow within the mixing chamber and the atomization mechanism at the nozzle exit to identify characteristic features of the two-phase flow. A shadowgraph droplet analyzer has also been applied to quantitatively compare the spray performance of the two atomizers in terms of droplet size distribution, droplet Sauter mean diameter (SMD), and the number of large droplets and ligaments within the spray field. The liquid breakup mechanism in the two atomizer configurations has also been quantitatively compared using shadowgraphy in the vicinity of the exit nozzle. The comparison demonstrated that the porous media air injector generates a higher number of smaller bubbles into the atomizer mixing chamber and consequently, a relatively constant GLR into the atomizer exit nozzle. The multihole injection generates large gas bubbles that leads to alternating liquid and gas slugs at the nozzle exit. This generates unsteadiness in the spray and the formation of large ligaments and droplets. The spray field of the porous media air injector, however, has a more steady spray behavior and generates a lower number of large droplets and ligaments. This indicates that bubble size relative to the exit nozzle size has an important impact on spray properties at low-GLR conditions.


Articles with similar content:

PHOSPHORESCENT FLOW TRACKING FOR QUANTITATIVE MEASUREMENTS OF LIQUID SPRAY DISPERSION
Atomization and Sprays, Vol.26, 2016, issue 3
W. van de Water, G. J. F. van Heijst, B. C. S. de Ruijter, Herman J. H. Clercx, Dennis D. van der Voort, N. J. Dam
EFFERVESCENT ATOMIZATION OF HIGH-VISCOSITY FLUIDS: PART I. NEWTONIAN LIQUIDS
Atomization and Sprays, Vol.1, 1991, issue 3
Paul E. Sojka, Harry N. Buckner
DROPLET CHARACTERIZATION OF A NOVEL ORIFICE SPRAY NOZZLE
Atomization and Sprays, Vol.15, 2005, issue 5
Weiping Liu, George H. Smith, Edward H. Owens, Mark T. Leonard
FLOW PATTERN OBSERVATIONS OF GASOLINE DISSOLVED CO2 INSIDE AN INJECTOR
Atomization and Sprays, Vol.16, 2006, issue 6
A. Rashkovan, Eran Sher
CHARACTERISTICS OF TRANSIENT, SWIRL-GENERATED, HOLLOW-CONE SPRAYS
Atomization and Sprays, Vol.16, 2006, issue 5
Julian T. Kashdan, John S. Shrimpton