Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
Heat Transfer Research
Fator do impacto: 0.404 FI de cinco anos: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Imprimir: 1064-2285
ISSN On-line: 2162-6561

Volumes:
Volume 50, 2019 Volume 49, 2018 Volume 48, 2017 Volume 47, 2016 Volume 46, 2015 Volume 45, 2014 Volume 44, 2013 Volume 43, 2012 Volume 42, 2011 Volume 41, 2010 Volume 40, 2009 Volume 39, 2008 Volume 38, 2007 Volume 37, 2006 Volume 36, 2005 Volume 35, 2004 Volume 34, 2003 Volume 33, 2002 Volume 32, 2001 Volume 31, 2000 Volume 30, 1999 Volume 29, 1998 Volume 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2017014564
pages 1693-1706

ANALYSIS OF HEAT TRANSFER AND SOLIDIFICATION CHARACTERISTICS OF Al−4.5Cu IN A TOP-SIDE POURING HIGH-SPEED TWIN-ROLL STRIP CASTER

Chinmaya Mund
Department of Mechanical Engineering, Institute of Technical Education and Research, Siksha 'O' Anusandhan University, Khandagiri, Bhubaneswar, Orissa, 751030, India
D. N. Thatoi
Department of Mechanical Engineering, Institute of Technical Education and Research, Siksha 'O' Anusandhan University, Khandagiri, Bhubaneswar, Orissa, 751030, India
Seshadev Sahoo
Department of Mechanical Engineering, Institute of Technical Education and Research, Siksha 'O' Anusandhan University, Khandagiri, Bhubaneswar, Orissa, 751030, India

RESUMO

Numerical modeling of heat transfer and solidification during twin-roll strip casting involves fluid flow, heat transfer, and phase change in the liquid metals. Heat flux at the solid–metal/roll surface should also be considered since solidification of the liquid metal occurs on the roll surface. In the present investigation, a comprehensive three-dimensional model of top-side pouring high-speed twin-roll strip casting of Al–4.5 wt.% Cu alloy has been developed. ANSYS 13.0 was used to model fluid flow, heat transfer, and solidification behavior during the top-side pouring of liquid Al–4.5 wt.% Cu alloy in a twin-roll strip caster and validated with experiment by measuring the cooling rate and dendritic arm spacing. From the simulation results it is found that the solidification was completed before the roll nip position and strong recirculation of the liquid metal occurs in the molten pool region. With increase in the nozzle diameter, the solidification end point exits towards the roll nip.


Articles with similar content:

DEVELOPMENT OF COLD THERMAL PLUMES INDUCED BY A ROTATING COLD SURFACE
Journal of Flow Visualization and Image Processing, Vol.2, 1995, issue 4
Genshi Kawashima, Wen-Jei Yang, Hiroshi Ohue
EVALUATION OF TEMPERATURE AND HEAT TRANSFER CONDITIONS IN METAL FORMING
International Heat Transfer Conference 11, Vol.20, 1998, issue
Patrick H. Oosthuizen, J. Jeswiet, W. Nshama
NUMERICAL ANALYSIS OF STEEL SOLIDIFICATION AND PARTICLE ENTRAPMENT IN A CONTINUOUS BILLET CASTER
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2017, issue
Suryanaman Chaube, Varnita Bajpai
Dynamics of entrapped air bubble during impact of high-velocity molten droplet on a solid substrate
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Arvind Kumar, Digvijay Singh, Rajesh Kumar Shukla
A Mathematical Model to Calculate the Fluidity of Pure Metals
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 1979, issue
M. Kolling, Ulrich Grigull