Inscrição na biblioteca: Guest
Portal Digital Begell Biblioteca digital da Begell eBooks Diários Referências e Anais Coleções de pesquisa
International Journal of Energetic Materials and Chemical Propulsion
ESCI SJR: 0.28 SNIP: 0.421 CiteScore™: 0.9

ISSN Imprimir: 2150-766X
ISSN On-line: 2150-7678

International Journal of Energetic Materials and Chemical Propulsion

DOI: 10.1615/IntJEnergeticMaterialsChemProp.2014010649
pages 471-477

CURE KINETICS OF POLY NITRATOMETHYL OXETANE WITH DIFFERENT ISOCYANATES STUDIED BY DIFFERENTIAL SCANNING CALORIMETRY

Kavita Ghosh
High Energy Materials Research Laboratory, Sutarwadi, Pune, India
Suman Pawar
High Energy Materials Research Laboratory, Sutarwadi, Pune, India
Arvind Kumar
Dept. of Mechanical Engineering, Indian Institute of Technology Kanpur Kanpur, Uttar Pradesh, 208016, India
Arunkanti Sikder
High Energy Materials Research Laboratory, Sutarwadi, Pune, India
Manoj Gupta
High Energy Materials Research Laboratory, Sutarwadi, Pune, India

RESUMO

This paper reports cure kinetics of poly nitratomethyl oxetane (PLN) with different isocyanates like isophorane di-isocyanate (IPDI) and hexamethylene di-isocyanate (HMDI). Reactions were monitored by differential scanning calorimetry (DSC) in the presence of two different cure catalysts namely di butyl tin di laurate (DBTDL) and ferric tris acetyl acetonate (FeAA) and their effect on the cure reaction was studied. Cure kinetics was evaluated using the multiple heating rate Ozawa method. The reactivity of two isocyanates and catalytic efficiencies were determined based on DSC reaction temperature, activation energy, and rate constants. Based on cure temperatures, FeAA catalyzed reactions have lower cure temperature than DBTDL catalyzed reactions, inferring that FeAA is a more active catalyst for PLN cure reactions. Rate constants (k) of FeAA catalyzed PLN cure reactions were higher than of DBTDL catalyzed reactions. The values of activation energies (Ea), pre-exponential factor, and rate constant also support the same trend. Completion of the curing process was monitored with the help of Fourier transform infrared. Viscosity buildup was measured with the help of rheometer by taking curing profiles for each system at 30° C and it followed the similar trend as determined by DSC.


Articles with similar content:

EXPERIMENTAL STUDY OF THERMAL CONDUCTIVITY OF BORIC ACID−WATER SOLUTIONS
Heat Transfer Research, Vol.50, 2019, issue 17
Nese Keklikcioğlu Çakmak
EFFICIENT REMOVAL OF ANIONIC DYE POLLUTANT BY NIMGAL LAYERED DOUBLE HYDROXIDES OF VARIABLE COMPOSITION
Catalysis in Green Chemistry and Engineering, Vol.1, 2018, issue 4
Ramesh Ch. Deka, Pankaj Bharali, Dipshikha Bharali
CATALYTIC WET AIR OXIDATION USING GRAPHENE OXIDE AND RUTHENIUM NANOPARTICLES SUPPORTED ON GRAPHENE OXIDE
Catalysis in Green Chemistry and Engineering, Vol.1, 2018, issue 3
Shrikant Y. Vemula, Prakash Vaidya
EXPERIMENTAL INVESTIGATION OF THERMAL CONDUCTIVITY AND HEAT CAPACITY OF COAL-WATER FUEL
International Journal of Energy for a Clean Environment, Vol.17, 2016, issue 2-4
Valeriya A. Pinchuk, T. A. Sharabura, Andrey Kuzmin
HETEROGENEOUS SYNTHESIS OF ETHYL BUTYRATE: PARAMETER OPTIMIZATION AND KINETIC STUDIES
Catalysis in Green Chemistry and Engineering, Vol.2, 2019, issue 1
Virendra K. Rathod, P. N. Dange