ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.5

ISSN 印刷: 2152-5102
ISSN オンライン: 2152-5110

巻:
巻 46, 2019 巻 45, 2018 巻 44, 2017 巻 43, 2016 巻 42, 2015 巻 41, 2014 巻 40, 2013 巻 39, 2012 巻 38, 2011 巻 37, 2010 巻 36, 2009 巻 35, 2008 巻 34, 2007 巻 33, 2006 巻 32, 2005 巻 31, 2004 巻 30, 2003 巻 29, 2002 巻 28, 2001 巻 27, 2000 巻 26, 1999 巻 25, 1998 巻 24, 1997 巻 23, 1996 巻 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v43.i3.20
pages 206-217

Secondary Flow Behaviour in Various Rounded-Edge Bifurcation T-Junctions and Its Relation to Head Loss

YB. Lukiyanto
Sanata Dharma University
I. N. G. Wardana
Mechanical Engineering Department, Brawijaya University Jln. MT. Haryono 167, Malang 65145, Indonesia
Widya Wijayanti
Mechanical Engineering Department, Brawijaya University Jln. MT. Haryono 167, Malang 65145, Indonesia
M. Agus Choiron
Mechanical Engineering Department, Brawijaya University Jln. MT. Haryono 167, Malang 65145, Indonesia

要約

Visualization of secondary flow behavior were carried out for the laminar flow (Re = 81) in a sharp-edged and rounded-edged 90° T-junction with an inlet flow perpendicular to both inline outlet flows orientation with a bifurcation ratio of 0.5. Particles were added to the fluid. The fluid was salt solution for density similarity with the particles, leading to eliminate the bouyance effect. Static pressures were measured at the inlet and one of the outlet channels by a U-manometer. The result shows that the rounded edge affected the recirculation secondary flow area and position leading to the reduction of the head loss. The image of the secondary flow demonstrates that a T-junction with the rounded edge with a rounded-edge radius ratio of 0.5 had a broader bifurcation area and a smaller secondary flow occupation area in the outlet channel, as compared to the sharp edge. The decreasing head loss ratio was 51 %. At rounded-edge radius ratio of 0 up to 1.5 part of secondary flow was located in the bifurcation area and the outlet area, whereas at rounded-edge radius ratio of 2 and of 2.5 it was located completely within the bifurcation area. Changing rounded-edge radius ratio from 1.5 to 2 reduced the head loss ratio up to 49.72 %.


Articles with similar content:

Numerical Fluid Flow and Heat Transfer Prediction of Rotating Tapered Channel
Journal of Enhanced Heat Transfer, Vol.16, 2009, issue 4
Luai M. Al-Hadhrami, Mehaboob Basha
NUMERICAL STUDY ON FLOW AND HEAT TRANSFER IN A RECTANGULAR CHANNEL WITH 45 DEG RIB TURBULATORS AND BLEED HOLES
Journal of Enhanced Heat Transfer, Vol.19, 2012, issue 5
Ya Jun Song, Zhong Yang Shen, Yong Hui Xie, Di Zhang
CFD Analysis of Post-Blowdown Thermal Behavior of a 19-Pin Fuel Bundle
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Rohit Kumar, Deb Mukhopadhyay, Manish Mishra, Onkar S. Gokhale, Pradeep Kumar Sahoo
NUMERICAL STUDY OF THE SECONDARY FLOW FORMATION OF A FLUID PASSING THROUGH A 90° ELBOW WITH SQUARE CROSS SECTION
4th Thermal and Fluids Engineering Conference, Vol.17, 2019, issue
O. M. Ayala, O. F. Ayala, Manuel Ayala
EFFECT OF CAVITATION IN CIRCULAR NOZZLE AND ELLIPTICAL NOZZLES ON THE SPRAY CHARACTERISTIC
Atomization and Sprays, Vol.20, 2010, issue 10
Choong-Won Lee, Sung Ryoul Kim, Kun Woo Ku, Jung Goo Hong