ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
Atomization and Sprays
インパクトファクター: 1.737 5年インパクトファクター: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN 印刷: 1044-5110
ISSN オンライン: 1936-2684

巻:
巻 30, 2020 巻 29, 2019 巻 28, 2018 巻 27, 2017 巻 26, 2016 巻 25, 2015 巻 24, 2014 巻 23, 2013 巻 22, 2012 巻 21, 2011 巻 20, 2010 巻 19, 2009 巻 18, 2008 巻 17, 2007 巻 16, 2006 巻 15, 2005 巻 14, 2004 巻 13, 2003 巻 12, 2002 巻 11, 2001 巻 10, 2000 巻 9, 1999 巻 8, 1998 巻 7, 1997 巻 6, 1996 巻 5, 1995 巻 4, 1994 巻 3, 1993 巻 2, 1992 巻 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.2012003917
pages 971-987

INTERNAL FLOW CHARACTERISTICS OF LIQUID-LIQUID SWIRL COAXIAL INJECTORS WITH DIFFERENT RECESS LENGTHS AND OXIDIZER-FUEL RATIOS

Sunghyuk Kim
Institute of Advanced Aerospace Technology, School of Mechanical and Aerospace Engineering, Seoul National University, San 56-1, Shillim-dong, Gwanak-gu, Seoul, 151-742, KOREA
Jungsoo Yoon
School of Mechanical and Aerospace Engineering, Seoul National University, 599 Gwanak-ro, Gwanak-gu, Seoul, 151-742, Korea
Youngbin Yoon
Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul, 08826, Republic of Korea

要約

In this study, the aim is to investigate the internal flow characteristics related to the oxidizer−fuel (O/F) ratio of a recessed swirl coaxial injector for gas generators and main combustors in liquid rocket engines. The mixing process of internal flow is very important in a recessed swirl coaxial injector; however, measuring internal flow is almost impossible except if using numerical analysis. This paper describes the design of a swirl coaxial injector that enables flow visualization and film thickness measurement and gives the results of cold flow tests using water as a simulant fluid. The injection conditions in the injector for the gas generator and main combustor were set to O/F ratios of 0.32 and 2.44 and the off-design points were set to 10% and 15%, respectively. Recess length varied by 1 mm for each case. The liquid film thickness variations after collision between two liquid flows were measured using the electrical conductance method. In addition, the characteristics of liquid film wave frequency and amplitude were analyzed based on liquid film thickness measurement and mixing time. This study confirms that liquid film becomes thinner after the mixing process. This is based on visualizing the internal flow and measuring liquid film thickness. The degree of the thinning of the liquid film varies with the momentum flux ratio according to the O/F ratio. An unstable internal flow was detected in the mixing process near the injector tip position.


Articles with similar content:

MEASUREMENT OF BREAKUP LENGTH OF CYLINDRICAL LIQUID JETS. APPLICATION TO LOW-PRESSURE CAR INJECTOR
Atomization and Sprays, Vol.11, 2001, issue 3
Christophe Dumouchel
Disintegration of Annular Liquid Sheet with Core Air Flow − Mode Classification
International Journal of Fluid Mechanics Research, Vol.24, 1997, issue 1-3
Si Hong Song, Sang Yong Lee, Chul Jin Choi
EFFECT OF GAS-LIQUID AXIAL VELOCITY CONTINUITY ON THE AXISYMMETRIC AND ASYMMETRIC INSTABILITIES OF A VISCOELASTIC LIQUID CORE IN A SWIRLING GASEOUS CO-FLOW
Atomization and Sprays, Vol.26, 2016, issue 1
Guodong Liu, Ming-Xi Tong, Qing-Fei Fu, Li-Jun Yang
DROPLET FORMATION FROM A THIN HOLLOW LIQUID JET WITH A CORE AIR FLOW
Atomization and Sprays, Vol.15, 2005, issue 5
Sang Yong Lee, Chul Jin Choi
DROPLET FORMATION FROM A THIN HOLLOW LIQUID JET WITH A CORE AIR FLOW
Atomization and Sprays, Vol.15, 2005, issue 4
Sang Yong Lee, Chul Jin Choi