ライブラリ登録: Guest
Begell Digital Portal Begellデジタルライブラリー 電子書籍 ジャーナル 参考文献と会報 リサーチ集
International Journal of Energetic Materials and Chemical Propulsion
ESCI SJR: 0.142 SNIP: 0.16 CiteScore™: 0.29

ISSN 印刷: 2150-766X
ISSN オンライン: 2150-7678

International Journal of Energetic Materials and Chemical Propulsion

DOI: 10.1615/IntJEnergeticMaterialsChemProp.v2.i1-6.270
pages 438-452

TEMPERATURE SENSITIVITY MEASUREMENTS AND REGRESSION BEHAVIOR OF A FAMILY OF BORON-BASED VERY HIGH BURNING RATE PROPELLANTS

R. M. Salizzoni
Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, USA
W. H. Hsieh
Department of Mechanical Engineering, The Pennsylvania State University, University Park, PA 16802, U.S.A.

要約

The combustion behaviors of three formulations of very high burning rate (VHBR) propellants are being studied. These formulations contain 0, 2, and 4% boron hydride, B10H10, the burning rate catalyst. Two diagnostic tools were used in this study: a realtime X-ray radiography (RTR) system with a high-pressure double-windowed (HPDW) test rig and a pressure and temperature controlled optical strand burner (OSB). The RTR system is used to obtain instantaneous X-ray images of the solid propellant grain as it burns during a transient test at pressure up to 340 MPa (50,000 psi). The optical strand burner maintains a steady pressure up to 41.4 MPa (6,000 psi) and allows the initial temperature of the strand to be set from −40°C to +70°C (−40°F to + 158°F).
For a typical RTR test using the HPDW test rig, the instantaneous, internal burning surface of a center-perforated grain was observed. The results show that the grain remained as a consolidated piece even at a high regression rate of 200 cm/s. From these images, instantaneous burning rates were deduced for all three formulations. These burning rates were compared with earlier results obtained by the authors from end-burning grains under similar transient conditions. These two sets of burning rates are in reasonable agreement.
The OSB was used to study the temperature sensitivity (σp) of VHBR propellants. Determining propellants' temperature sensitivities as functions of pressure and temperature is important in the study of transient burning phenomena. It was found that σp increases as initial temperature (Ti) decreases. As a result of a slope break in the burning rate, σp exhibits discontinuities as functions of pressure and Ti.
From a recovered sample which was extinguished at 331 MPa (48,000 psi), the burning surface was found to be non-smooth and covered with a melt layer containing many small indentations.


Articles with similar content:

TRANSIENT BURNING BEHAVIOR OF SOLID PROPELLANTS
International Journal of Energetic Materials and Chemical Propulsion, Vol.3, 1994, issue 1-6
Yeu-Cherng Lu, F. R. Schwam, Y. J. Yim
BURNING RATE CHARACTERIZATION OF OXSOL LIQUID OXIDIZER
International Journal of Energetic Materials and Chemical Propulsion, Vol.5, 2002, issue 1-6
J. W. Mordosky, George C. Harting, T. T. Cook, Baoqi Zhang
COMPOSITE PROPELLANT EXTINCTION BY LASER ENERGY PULSE
International Journal of Energetic Materials and Chemical Propulsion, Vol.4, 1997, issue 1-6
Claudio Zanotti, Piero Giuliani
TRANSIENT BURNING BEHAVIOR OF PHASE-STABILIZED AMMONIUM NITRATE BASED AIRBAG PROPELLANT
International Journal of Energetic Materials and Chemical Propulsion, Vol.11, 2012, issue 5
Eric Boyer, Jonathan T. Essel, Baoqi Zhang, Kenneth K. Kuo
INVESTIGATION OF BORON IGNITION AND COMBUSTION BY MEANS OF FAST CINESPECTROGRAPHY
International Journal of Energetic Materials and Chemical Propulsion, Vol.2, 1993, issue 1-6
Sergey N. Pen'kov