Library Subscription: Guest
Begell Digital Portal Begell Digital Library eBooks Journals References & Proceedings Research Collections
Atomization and Sprays
IF: 1.737 5-Year IF: 1.518 SJR: 0.814 SNIP: 1.18 CiteScore™: 2.2

ISSN Print: 1044-5110
ISSN Online: 1936-2684

Volumes:
Volume 30, 2020 Volume 29, 2019 Volume 28, 2018 Volume 27, 2017 Volume 26, 2016 Volume 25, 2015 Volume 24, 2014 Volume 23, 2013 Volume 22, 2012 Volume 21, 2011 Volume 20, 2010 Volume 19, 2009 Volume 18, 2008 Volume 17, 2007 Volume 16, 2006 Volume 15, 2005 Volume 14, 2004 Volume 13, 2003 Volume 12, 2002 Volume 11, 2001 Volume 10, 2000 Volume 9, 1999 Volume 8, 1998 Volume 7, 1997 Volume 6, 1996 Volume 5, 1995 Volume 4, 1994 Volume 3, 1993 Volume 2, 1992 Volume 1, 1991

Atomization and Sprays

DOI: 10.1615/AtomizSpr.v13.i23.90
11 pages

ON QUANTIFYING INTERFACIAL THERMAL RESISTANCE AND SURFACE ENERGY DURING MOLTEN MICRODROPLET SURFACE DEPOSITION

D. Attinger
Department of Mechanical Engineering, State University of New York at Stony Brook, Stony Brook, New York, USA
Dimos Poulikakos
Laboratory of Thermodynamics in Emerging Technologies, Institute of Energy Technology Mechanical and Process Engineering Department, ETH Zurich, Switzerland

ABSTRACT

Understanding and controlling the deposition of a molten microdroplet on a colder substrate with simultaneous heat transfer and solidification is of central importance to a host of technologies, exemplified by novel methods of electronic microchip manufacturing. The physics of the interfaciat phenomena involved are to date only partially understood. For instance, the transient resistance to heat transfer at the droplet—substrate interface cannot be quantified theoretically, and adequate experimental data are lacking. Serious obstacles to experimental determination are the very short time and length scales involved (of the order of micrometers: and microseconds). In the present article, a numerical modeling for droplet impact and solidification based on the Navier-Stokes and energy equations is used in order to reproduce transient measurements of the deposition of a eutectic Pb-Sn microdroplet on a multilayer wafer. The resistance to heal transfer at the droplet—wafer interface and the surface energy of the molten microdroplet are determined by matching numerical and experimental results. This successfully demonstrated indirect method is of interest if direct transient thermal resistance data are not available (as is very often the case).


Articles with similar content:

COMBINED EXPERIMENTAL AND NUMERICAL SIMULATION OF CONVECTIVE TRANSPORT
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2014, issue
Yogesh Jaluria
HYDRODYNAMIC AND KINETIC MODELS OF DROPLET HEATING AND EVAPORATION: ANALYSIS AND APPLICATIONS
ICHMT DIGITAL LIBRARY ONLINE, Vol.13, 2008, issue
Morgan R. Heikal, Sergey Martynov, Sergei S. Sazhin, Irina N. Shishkova
HEAT TRANSFER PHENOMENA DURING CONTINUOUS CASTING OF ALUMINIUM ALLOYS
International Heat Transfer Conference 10, Vol.1, 1994, issue
L. Katgerman
A Non-Intrusive Inverse Problem Technique for the Identification of Contact Failures in Double-Layered Composites
International Heat Transfer Conference 15, Vol.24, 2014, issue
Luiz A.S. Abreu, HELCIO ORLANDE, Carlos J.S. Alves, Marcelo Jose Colaco
NUMERICAL SIMULATION OF THE EFFECT OF CONTACT ANGLE ON THE THERMAL RESPONSE OF THE SOLID DURING NUCLEATE POOL BOILING
Interfacial Phenomena and Heat Transfer, Vol.2, 2014, issue 4
Eduardo Aktinol, Vijay K. Dhir