Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.9

ISSN Imprimer: 2152-5102
ISSN En ligne: 2152-5110

Volumes:
Volume 47, 2020 Volume 46, 2019 Volume 45, 2018 Volume 44, 2017 Volume 43, 2016 Volume 42, 2015 Volume 41, 2014 Volume 40, 2013 Volume 39, 2012 Volume 38, 2011 Volume 37, 2010 Volume 36, 2009 Volume 35, 2008 Volume 34, 2007 Volume 33, 2006 Volume 32, 2005 Volume 31, 2004 Volume 30, 2003 Volume 29, 2002 Volume 28, 2001 Volume 27, 2000 Volume 26, 1999 Volume 25, 1998 Volume 24, 1997 Volume 23, 1996 Volume 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v36.i5.10
pages 391-413

Numerical Investigation of Impinging Two-Dimensional Jet on an Inclined Flat Plate

A. Abdel-Fattah
Department of Mechanical Power Engineering, Faculty of Engineering Menoufiya University, Shebin El-Kom
Mostafa A. Abd El-Baky
Department of Mechanical Power Engineering, Faculty of Engineering Menoufiya University, Shebin El-Kom, Egypt

RÉSUMÉ

The flow and thermal fields in a turbulent jet, impinging on a flat plate at an angle of incidence, has been studied numerically .The plate has a constant heat flux that transfers to the jet fluid and causes a temperature gradient in fluid. Computations are carried out with k-ε and v'2-f turbulence models. The flow is assumed to be two dimensional, steady incompressible and turbulent. The finite volume method is used to solve the two dimensional conservation equations of mass, momentum, energy and v'2-f turbulence models. The finite volume method is formulated to suit the general grid system. The flow characteristics were studied by changing plate inclination as 0° ≤ θ ≤ 45°, the distance between the nozzle exit and plate within 2 ≤ H/b ≤ 12, and the Reynolds number in the range 2500 ≤ Re ≤ 12000. The results show that the location of the maximum heat transfer was affected by the angle of inclination. The location of the maximum heat transfer shifts towards the up hill side of the plate by increasing the inclination angle. The value of the maximum Nusselt number increases with increasing nozzle-to-plate spacing. The pressure coefficient increases as the distance between the nozzle and pate decreases.


Articles with similar content:

Forced convection
NUMERICAL SIMULATION OF TRANSIENT COOLING EFFECT WITH WALL MASS INJECTION BEHIND THE BACKSTEP

ICHMT DIGITAL LIBRARY ONLINE, Vol.11, 2004, issue
Yue-Tzu Yang, Kuo-Teng Tsai
LAMINAR FREE CONVECTION BETWEEN TWO VERTICAL PARALLEL PLATES WITH DIFFERENT RIB HEIGHTS AND POSITIONS
International Heat Transfer Conference 16, Vol.9, 2018, issue
Viktor I. Terekhov, Khalil F. Yassin, Ali L. Ekaid
FLOW AND HEAT TRANSFER CHARACTERISTIC OF TURBULENT PLANE WALL JET INTERACTING WITH COFLOWING FREESTREAM
Proceedings of the 24th National and 2nd International ISHMT-ASTFE Heat and Mass Transfer Conference (IHMTC-2017), Vol.0, 2017, issue
Sushil Kumar Rathore, Satish Kumar Yadav
COMPUTATIONAL STUDY OF HEAT TRANSFER FROM A CONFINED TURBULENT SLOT JET IMPINGING ON A MOVING PLATE
International Heat Transfer Conference 13, Vol.0, 2006, issue
Muhammad Ali Rob Sharif, A. Banerjee
Numerical Investigation of Flow and Heat Transfer around Two Semi-Circular Cylinders with a Splitter Plate
Heat Transfer Research, Vol.42, 2011, issue 7
Hadi Heidary, Mostafa Nourollahi, Kurosh Sedighi, Mousa Farhadi