Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Heat Transfer Research
Facteur d'impact: 0.404 Facteur d'impact sur 5 ans: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Imprimer: 1064-2285
ISSN En ligne: 2162-6561

Volumes:
Volume 50, 2019 Volume 49, 2018 Volume 48, 2017 Volume 47, 2016 Volume 46, 2015 Volume 45, 2014 Volume 44, 2013 Volume 43, 2012 Volume 42, 2011 Volume 41, 2010 Volume 40, 2009 Volume 39, 2008 Volume 38, 2007 Volume 37, 2006 Volume 36, 2005 Volume 35, 2004 Volume 34, 2003 Volume 33, 2002 Volume 32, 2001 Volume 31, 2000 Volume 30, 1999 Volume 29, 1998 Volume 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.2016011691
pages 1025-1045

LBM SIMULATION OF FRICTION FACTOR AND HEAT TRANSFER ON THE MOVING LID OF A TRIANGULAR ENCLOSURE

M.A. Taher
Department of Mechanical and Automotive Engineering, Pukyong National University, Busan 608-739, Korea
Heuy Dong Kim
Department of Mechanical Engineering, Andong National University, Andong 760-749, Korea
Y. W. Lee
Department of Mechanical and Automotive Engineering, Pukyong National University, Busan 608-739, Korea

RÉSUMÉ

A lattice Boltzmann study has been performed to analyze the combined force and free convection, known as mixed convection, flow and heat transfer process in a lid-driven triangular enclosure. The thermal lattice Boltzmann method (TLBM), based on the Boltzmann equation (BE), has been used as an alternative to traditional methods based on the Navier–Stokes equations for this study. The mixed convection parameter, called the Richardson number (Ri), provides an important measurement of the thermal natural convection forces relative to the mechanically induced lid-driven forced convection effects. The results are presented as velocity and temperature profiles as well as stream function and temperature contours for a wide range of dimensionless parameter (Ri) and Reynolds number (Re). Typical results for the skin friction and heat transfer on a moving lid are also presented. It is found that both the average skin friction and heat transfer rate decreased and increased slightly with increasing Ri. However, they are found to change significantly with increasing Reynolds number. Finally, the simulation results have been compared with published numerical results and the agreement is found to be very reasonable and satisfactory.


Articles with similar content:

THE EFFECT OF BUOYANCY ON VORTEX SHEDDING AND ENTROPY GENERATION OF A HEATED SQUARE CYLINDER
Computational Thermal Sciences: An International Journal, Vol.2, 2010, issue 6
R. Harish, K. Venkatasubbaiah
HIGH ACCURACY NUMERICAL APPROACH FOR NON-SIMILAR MIXED CONVECTION BOUNDARY LAYER FLOW OVER A HORIZONTAL PLATE
Computational Thermal Sciences: An International Journal, Vol.2, 2010, issue 4
K. Venkatasubbaiah
Natural Convection Heat Transfer from A Vertical Flat Plate with Phase Change Material Suspensions
Journal of Enhanced Heat Transfer, Vol.4, 1997, issue 1
Miloud Harhira, Subrata Sengupta, Sanjai K. Roy
GEOMETRY EFFECTS ON CRITICAL CONDUCTIVITY RATIO AND WALL THICKNESS FOR CONJUGATE NATURAL CONVECTION IN ECCENTRIC ANNULI
International Heat Transfer Conference 13, Vol.0, 2006, issue
Maged A. I. El-Shaarawi, A. Jamal
MIXED CONVECTION JET IMPINGEMENT COOLING OF A RECTANGULAR SOLID HEAT SOURCE IMMERSED IN A POROUS LAYER
Journal of Porous Media, Vol.18, 2015, issue 4
Nawaf H. Saeid