Abonnement à la biblothèque: Guest
Portail numérique Bibliothèque numérique eBooks Revues Références et comptes rendus Collections
Heat Transfer Research
Facteur d'impact: 0.404 Facteur d'impact sur 5 ans: 0.8 SJR: 0.264 SNIP: 0.504 CiteScore™: 0.88

ISSN Imprimer: 1064-2285
ISSN En ligne: 2162-6561

Volumes:
Volume 50, 2019 Volume 49, 2018 Volume 48, 2017 Volume 47, 2016 Volume 46, 2015 Volume 45, 2014 Volume 44, 2013 Volume 43, 2012 Volume 42, 2011 Volume 41, 2010 Volume 40, 2009 Volume 39, 2008 Volume 38, 2007 Volume 37, 2006 Volume 36, 2005 Volume 35, 2004 Volume 34, 2003 Volume 33, 2002 Volume 32, 2001 Volume 31, 2000 Volume 30, 1999 Volume 29, 1998 Volume 28, 1997

Heat Transfer Research

DOI: 10.1615/HeatTransRes.v40.i8.40
pages 777-792

Development and Power Performance Test of a Small Three-Blade Horizontal-Axis Wind Turbine

K. R. Ajao
Department of Mechanical Engineering, University of Ilorin, Ilorin, Nigeria
Isaac Kayode Adegun
Department of Mechanical Engineering, University of Ilorin, Ilorin, Nigeria

RÉSUMÉ

The parameterization, installation, and testing of a locally developed three-blade horizontal-axis wind turbine were carried out. The turbine blades were fabricated from Mansonia Altissima wood because of its availability, good strength, and resistance to both fatigue and soaking, with a rotor swept area of 3.65 m2 and the blade angle of attack was experimentally determined to be 7°. The turbine was installed on the roof top of the University of Ilorin, Faculty of Engineering Central Workshop Building at a hub height of 14.9 m from the ground level while the turbine generator was sourced locally. The direct current (d.c.) power output of the test turbine was measured at the battery bank terminal by a Power Analyzer and a direct current (d.c.) to alternating current (a.c.) inverter converts the d.c. power output to a.c. power and was measured by a digital wattmeter. An anemometer with a data logger installed on a meteorological tower (MET) measured the wind speed and direction over the test period. The cut-in wind speed, that is, the speed at which the wind turbine starts to produce power was determined to be 3.5 m/sec. One minutes averages of wind speed and power output was used to determine the power curve for the wind turbine. Measured power increase consistently with increased wind speed and the power curve obtained compared fairly well with standard power curves.

RÉFÉRENCES

  1. Ajao, K. R., Development and Performance Assessment of a Small Horizontal-axis Wind Turbine.

  2. Vermeer, L. J., Sorensen, J. N., and Crespo, A., Wind turbine wake aerodynamics.

  3. Adegoke, C. O. and Anjorin, A. S., Wind as an alternative energy source.

  4. Iloeje, O. C., Overview of Renewable Energy in Nigeria, Opportunities for Rural Development and Development of a Renewable Master Plan, Energy Commission of Nigeria, Presented at the Renewable Energy Conference "ENERGETIC SOLUTION", Abuja/Calabar, 21-26 November 2004.

  5. Okafor, N. F. and Hofmann, W., Recent developments in wind energy conversion technology and their benefits to Nigeria's power generation needs. In: Proc. 35th Annual Conference of Nigerian Society of Engineers, Abuja, November 2000.

  6. Muljadi, E. and Green, J., Cogging Torque Reduction in a Permanent Magnet Wind Turbine Generator.


Articles with similar content:

A NOVEL DESIGN FOR VERTICAL AXIS WIND TURBINE
Second Thermal and Fluids Engineering Conference, Vol.17, 2017, issue
Luz Amaya, Reza Ghodsi
MEASUREMENTS OF DEFORMATION OF THE ADAPTIVE WING LEADING EDGE IN A WIND TUNNEL BY THE VIDEOGRAMMETRY METHOD
TsAGI Science Journal, Vol.45, 2014, issue 8
Vladimir Petrovich Kulesh
SHEAR STRENGTH COMPUTATION OF REINFORCED CONCRETE BEAMS STRENGTHENED WITH COMPOSITE MATERIALS
Composites: Mechanics, Computations, Applications: An International Journal, Vol.3, 2012, issue 3
Paolo Foraboschi
Heat transfer coefficient and pressure drop characteristics of R410A condensation during upward flow in vertical smooth and micro-fin tubes
Second Thermal and Fluids Engineering Conference, Vol.43, 2017, issue
Yunxiao Yang , Li Jia, Qi Peng
Correlation Between the Critical Heat Flux and the Fractal Surface Roughness of Zirconium Alloy Tubes
Journal of Enhanced Heat Transfer, Vol.8, 2001, issue 2
R. W. L. Fong, Thambiayah Nitheanandan, D. B. Sanderson, G. A. McRae, C. E. Coleman