Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Journal of Porous Media
Factor de Impacto: 1.752 Factor de Impacto de 5 años: 1.487 SJR: 0.43 SNIP: 0.762 CiteScore™: 2.3

ISSN Imprimir: 1091-028X
ISSN En Línea: 1934-0508

Volumes:
Volumen 24, 2021 Volumen 23, 2020 Volumen 22, 2019 Volumen 21, 2018 Volumen 20, 2017 Volumen 19, 2016 Volumen 18, 2015 Volumen 17, 2014 Volumen 16, 2013 Volumen 15, 2012 Volumen 14, 2011 Volumen 13, 2010 Volumen 12, 2009 Volumen 11, 2008 Volumen 10, 2007 Volumen 9, 2006 Volumen 8, 2005 Volumen 7, 2004 Volumen 6, 2003 Volumen 5, 2002 Volumen 4, 2001 Volumen 3, 2000 Volumen 2, 1999 Volumen 1, 1998

Journal of Porous Media

DOI: 10.1615/JPorMedia.v10.i2.30
pages 137-150

Experimental Evaluation of Evaporation Enhancement with Porous Media in Liquid-Fueled Burners

Chendhil Periasamy
Combustion and Flame Dynamics Laboratory, School of Aerospace and Mechanical Engineering, 865 Asp Ave, Room 212, The University of Oklahoma, Norman, OK 73019; and Now at Air Liquide R&D, Newark, DE 19702, USA
Sathish K. Sankara-Chinthamony
Combustion and Flame Dynamics Laboratory, School of Aerospace and Mechanical Engineering, 865 Asp Ave, Room 212, The University of Oklahoma, Norman, OK 73019, USA
Subramanyam R. Gollahalli
Combustion and Flame Dynamics Laboratory, School of Aerospace and Mechanical Engineering, 865 Asp Ave, Room 212, The University of Oklahoma, Norman, OK 73019, USA

SINOPSIS

Potential benefits of using a porous medium to enhance evaporation in liquid-fueled burners have been experimentally evaluated. An open-cell, silicon carbide-coated, carbon-carbon ceramic foam was used as a porous medium. Aviation-type kerosene was sprayed into a coflowing, preheated air environment using an air-blast atomizer, and the spray subsequently entered the porous medium. The minimum combustion heat feedback rate required for complete vaporization and the vapor concentration downstream of the porous medium were measured. Surface temperature measurements showed that the temperature of the porous medium was uniform within 10 K. The minimum heat feedback rate required for complete vaporization increased as the distance between the porous medium and the injector was decreased. Under the present conditions, with porous media and combustion heat feedback, complete vaporization was achieved at a coflow air temperature of 400 K. Without porous media, however, a minimum coflow air temperature of 500 K was required to achieve the same quality of evaporation. Measurements revealed that a combustion heat feedback rate of 1% produced average vapor concentrations of 63% and 43% more than that with no heat feedback at equivalence ratios of 0.3 and 0.6, respectively.


Articles with similar content:

NUMERICAL MODELING OF EVAPORATION ENHANCEMENT OF AVIATION-GRADE KEROSENE SPRAY IN POROUS MEDIA COMBUSTORS
Journal of Porous Media, Vol.13, 2010, issue 8
Chendhil Periasamy, Subramanyam R. Gollahalli
ELECTRIC POWER GENERATION FROM COMBUSTION IN POROUS MEDIA
Journal of Porous Media, Vol.19, 2016, issue 10
Pedro San Martin, Valeri Bubnovich, Nina Orlovskaya, Luis Henriquez-Vargas, Hernan A. Gonzaiez-Rojas
Enhanced Pool Boiling CHF in FC-72 from a Modulated Porous Layer Coating
Journal of Enhanced Heat Transfer, Vol.13, 2006, issue 2
Klemen Ferjancic, D. Rajselj, Iztok Golobic
CONDENSATION OF ATMOSPHERIC PRESSURE STEAM ON INTEGRAL-FIN TUBES - EFFECT OF FIN HEIGHT AND VAPOUR VELOCITY
International Heat Transfer Conference 13, Vol.0, 2006, issue
S. Namasivayam
COMBUSTION OF BIMODAL ALUMINUM PARTICLES AND ICE MIXTURES
International Journal of Energetic Materials and Chemical Propulsion, Vol.11, 2012, issue 3
Steven F. Son, Grant A. Risha, Vigor Yang, Terrence L. Connell, Jr., Richard A. Yetter