Suscripción a Biblioteca: Guest
Portal Digitalde Biblioteca Digital eLibros Revistas Referencias y Libros de Ponencias Colecciones
Journal of Long-Term Effects of Medical Implants
SJR: 0.145 SNIP: 0.491 CiteScore™: 0.89

ISSN Imprimir: 1050-6934
ISSN En Línea: 1940-4379

Journal of Long-Term Effects of Medical Implants

DOI: 10.1615/JLongTermEffMedImplants.v16.i1.60
pages 51-59

Setting Properties of Four Acrylic and Two Calcium-Phosphate Cements Used in Vertebroplasty

Gamal Baroud
Canada Research Chair in Skeletal Reconstruction and Biomedical Engineering Director, Biomechanics Lab, Université de Sherbrooke, Canada
Tara Swanson
Co-operative Education Program, Faculty of Kinesiology, Simon Fraser University, Burnaby, BC, Canada
Thomas Steffen
Orthopaedic Research Laboratory, Division of Orthopaedic Surgery, McGill University, Montreal, QC, Canada

SINOPSIS

Study design. Experimental study conducted in the laboratory with six different bone cements. Objectives. To isolate the thermal properties of conventional and emerging bone cements used in vertebroplasty and to characterize their setting behavior. Summary of background data. The heat released during setting has been linked to the desirable effects of pain relief and tumor destruction and to the undesirable effect of thermal necrosis of surrounding tissue. However, there are currently no studies that disconnect the exothermic reaction of the cements from the media in which they occur. Before the combined thermal effect is examined, it is important to understand the setting properties of cements alone. Methods. Thirty independent experiments were conducted with four PMMA cements (Cranioplastic, Vertebroplastic, Palacos LV-40, Antibiotic Simplex) and two calcium-phosphate cements (chronOS Inject and Biopex) in accordance with ASTM standard F 451-99a. A thermocouple was placed in the center of the cement mass, and the temperature-versus-time measurements were recorded. Results. The calcium-phosphate cements took over half an hour to reach their maximum temperature, which was only 3−4 °C higher than the ambient temperature. The temperature increase for the acrylic cements was between 16 and 23 °C, and it took about 15 minutes to reach the maximum temperature. The variation within the groups was also important. Conclusion. The exothermic reaction of calcium-phosphate cements appears to be insignificant. Although the acrylic cements release considerably greater heat in a much shorter time period, it does not appear that their temperature is sufficiently high to cause extensive thermal injury. However, variations within each group must be considered along with the intended use when deciding on the cement to be used.


Articles with similar content:

Chromosomal Aberration Analysis in Chronically Exposed Radiation Workers
Journal of Environmental Pathology, Toxicology and Oncology, Vol.23, 2004, issue 3
Kshiti B. Anjaria, Badanidiyoor S. Rao
White Button Mushroom, Agaricus bisporus (Agaricomycetes), and a Probiotics Mixture Supplementation Correct Dyslipidemia without Influencing the Colon Microbiome Profile in Hypercholesterolemic Rats
International Journal of Medicinal Mushrooms, Vol.22, 2020, issue 3
Zahid Kamran, Haseeb Anwar, Farhan Asad, Aziz-ul-Rahman, Muhammad Umar Sohail, Muhammad Irfan Ullah, Hadi M. Yassine
Designing optimal heat transfer experiments − A case study
International Heat Transfer Conference 12, Vol.24, 2002, issue
L. van Belle, Ashley F. Emery
Measurement of Temperature Distribution for the Hydrate Formation and Dissociation in Porous Media
International Heat Transfer Conference 15, Vol.55, 2014, issue
Shenglong Wang, Yongchen Song, Yuechao Zhao, Jiafei Zhao, Lanlan Jiang, Mingjun Yang
TEMPERATURE SENSITIVITY OF GRANULAR PROPELLANTS USING A CONDITIONED CLOSED BOMB
International Journal of Energetic Materials and Chemical Propulsion, Vol.13, 2014, issue 1
Baoqi Zhang, Kenneth K. Kuo, Heath T. Martin