Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.5

ISSN Druckformat: 2152-5102
ISSN Online: 2152-5110

Volumes:
Volumen 46, 2019 Volumen 45, 2018 Volumen 44, 2017 Volumen 43, 2016 Volumen 42, 2015 Volumen 41, 2014 Volumen 40, 2013 Volumen 39, 2012 Volumen 38, 2011 Volumen 37, 2010 Volumen 36, 2009 Volumen 35, 2008 Volumen 34, 2007 Volumen 33, 2006 Volumen 32, 2005 Volumen 31, 2004 Volumen 30, 2003 Volumen 29, 2002 Volumen 28, 2001 Volumen 27, 2000 Volumen 26, 1999 Volumen 25, 1998 Volumen 24, 1997 Volumen 23, 1996 Volumen 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.2018019635
pages 139-152

ANALYSIS AND INVESTIGATION OF THE ADAPTIVE TECHNIQUE TO SIMULATE THE SYNTHETIC JET SYSTEM

Khadidja Boualem
Université des Sciences et de la Technologie d'Oran Mohamed Boudiaf, USTO-MB, BP 1505, El M'naouer, 31000 Oran Algérie
Tayeb Yahiaoui
Laboratoire d’Aéronautique et Systèmes Propulsive, Université des Sciences et de la Technologie d’Oran - Mohamed-Boudiaf, Algeria
Abbes Azzi
Laboratory of Naval Aero-Hydrodynamic, Faculty of Mechanical Engineering, Oran University of Sciences and Technology, PO Box 1505, El-Mnaouar Oran, Algeria

ABSTRAKT

Synthetic jets are used in several fields because of their simplicity and efficiency, such as active cooling to improve thermal management and active control of the boundary layer separation in various application practices, in order to enhance aerodynamic performance. These devices are generated by a piezoelectric diaphragm embedded in a cavity, through an orifice, in a periodic manner. Also, they have the benefit of being compact with zero net mass flux. To study the synthetic jets experimentally, many practical devices can be used, such as artificial excitation, micro valves, pneumatic, etc. Analytically, several approaches were previously used, such as the theory of plate deformation, a lumped element model based on electroacoustic theory, periodic inlet velocity profiles, etc. In the present study, a numerical approach based on a moving mesh method is proposed in the modeling field as a new approach. The mesh deformation is an important approach component for solving problems with moving boundaries or deformable bodies. The motion might be imposed or an implicit part of a coupled fluid-structure simulation. The new model was compared to theory of plates deformation approach, which has previously been used, and both are validated by the experimental data (given in a NASA workshop on Synthetic Jets Validation CFDVAL2004) to evaluate the performed one. Results show that the flow behavior is reproduced correctly by the new approach.


Articles with similar content:

Modelling and simulation of single- and multi-phase axisymmetric impinging jets
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2015, issue
M. Garlick, Timothy J. Craft, Michael Fairweather
VISUALISATION NUMERICAL SIMULATION OF AN IMPINGING SQUARE JET USING VIRTUAL REALITY TECHNOLOGY
International Heat Transfer Conference 13, Vol.0, 2006, issue
Loay Younis Aldabbagh , Hamed Farahani Manesh, Majid Hashemipour
AEROELASTIC BEHAVIOUR OF BRIDGES SUBJECTED TO WIND FLOWS
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2009, issue
Ton Hoang Mai, K. Zibouche, R. Belakroum, Mahfoud Kadja
An Investigation into Momentum and Temperature Fields of a Meso-Scale Slot Synthetic Jet for a Small Jet-to-Surface Spacing
International Heat Transfer Conference 15, Vol.23, 2014, issue
M. Baris Dogruoz, Omidreza Ghaffari, Mehmet Arik
Feasibility Study of Hybrid LES/RANS Model for the Flow Over an Aerodynamic Body
ICHMT DIGITAL LIBRARY ONLINE, Vol.0, 2012, issue
Ryo S. Amano