Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.9

ISSN Druckformat: 2152-5102
ISSN Online: 2152-5110

Volumes:
Volumen 47, 2020 Volumen 46, 2019 Volumen 45, 2018 Volumen 44, 2017 Volumen 43, 2016 Volumen 42, 2015 Volumen 41, 2014 Volumen 40, 2013 Volumen 39, 2012 Volumen 38, 2011 Volumen 37, 2010 Volumen 36, 2009 Volumen 35, 2008 Volumen 34, 2007 Volumen 33, 2006 Volumen 32, 2005 Volumen 31, 2004 Volumen 30, 2003 Volumen 29, 2002 Volumen 28, 2001 Volumen 27, 2000 Volumen 26, 1999 Volumen 25, 1998 Volumen 24, 1997 Volumen 23, 1996 Volumen 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v25.i1-3.370
pages 422-429

The Design and Testing of a Fluid Bed Incinerator which Will Be Used to Investigate the Burning of Waste Chemicals

Joe Deans
Department of Mechanical Engineering, University of Auckland, Auckland, New Zealand
S. T. Choi
Department of Mechanical Engineering, University of Auckland, New Zealand
M. L. Allen
Department of Chemical Engineering, University of Auckland, New Zealand

ABSTRAKT

The destruction and disposal of liquid waste chemicals is a perennial problem which is gaining increasing importance. One possible method of destroying these chemicals is to incinerate them within a fluid bed where there is a relatively long residence time and the combustion of the chemicals is completed. To aid the investigation of this process a 0.17 m diameter fluid bed incinerator has been designed, constructed and tested. This report describes these activities and the tests which were performed on a range "commercial" waste chemicals. The precise composition of these chemicals was continuously changing though they were generally low vapor pressure solvents or oils contaminated with water.
During the incineration tests the effectiveness of the combustion process was determined by monitoring the emission levels of oxygen, carbon monoxide and unburnt hydrocarbons. The results of the tests showed that: i) It was possible to achieve emission levels of 5% Carbon monoxide and less than 100 ppm unburnt hydrocarbons, and that, ii) The optimum operating conditions for the bed were achieved when the exhaust gas contained 5% oxygen.


Articles with similar content:

EXPERIMENTAL AND SIMULATION THERMAL ANALYSES FOR STAGED CO-INCINERATION OF SOLID AND LIQUID WASTES IN ROTARY KILN
International Heat Transfer Conference 16, Vol.20, 2018, issue
B. Zhang, S. Li, Weitong Liu
SUBMICRON PARTICLES FORMATION BY CONDENASATION AT COALS BURNING. NUMERICAL SIMULATION
International Heat Transfer Conference 16, Vol.7, 2018, issue
Naum Moiseevich Kortsenshteyn, Leonid V. Petrov
PLASMA ARC VITRIFICATION OF FLY-ASHES FROM MUNICIPAL WASTE INCINERATION PLANT
Progress in Plasma Processing of Materials, 1997, Vol.1, 1997, issue
C. Vandensteendam, S. Megy, P. Roumilhac, Jean Marie Baronnet
PLASMA TECHNOLOGIES: BROADENING THE OPPORTUNITY FOR WASTE PROCESSING
High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes, Vol.16, 2012, issue 3
I. I. Kadyrov, S. A. Dmitriev, F. A. Lifanov, V. A. Gorbunov, M. A. Polkanov, A. P. Kobelev
CONSIDERATIONS ON EXPERIMENTAL STUDIES OF VEGETABLE CHAR COMBUSTION IN FLUIDIZED BED
International Journal of Energy for a Clean Environment, Vol.10, 2009, issue 1-4
N. Rangel, Carlos Pinho