Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
International Journal of Fluid Mechanics Research
ESCI SJR: 0.206 SNIP: 0.446 CiteScore™: 0.9

ISSN Druckformat: 2152-5102
ISSN Online: 2152-5110

Volumes:
Volumen 47, 2020 Volumen 46, 2019 Volumen 45, 2018 Volumen 44, 2017 Volumen 43, 2016 Volumen 42, 2015 Volumen 41, 2014 Volumen 40, 2013 Volumen 39, 2012 Volumen 38, 2011 Volumen 37, 2010 Volumen 36, 2009 Volumen 35, 2008 Volumen 34, 2007 Volumen 33, 2006 Volumen 32, 2005 Volumen 31, 2004 Volumen 30, 2003 Volumen 29, 2002 Volumen 28, 2001 Volumen 27, 2000 Volumen 26, 1999 Volumen 25, 1998 Volumen 24, 1997 Volumen 23, 1996 Volumen 22, 1995

International Journal of Fluid Mechanics Research

DOI: 10.1615/InterJFluidMechRes.v24.i4-6.90
pages 526-533

A Study of the Injection of Twin Pulsed High Speed Liquid Jets Across Transonic Region

H.-H. Shi
Department of Mechanical Engineering, Nagoya Institute of Technology, Showa-ku, Nagoya, Japan
Motoyuki Itoh
Department of Mechanical Engineering, Nagoya Institute of Technology, Showa-ku, Nagoya, Japan

ABSTRAKT

A study of the injection of twin pulsed liquid jets ranging from subsonic to supersonic using a high-pressure helium gas gun was conducted. Twin diverging, parallel or impinging jets and single jet were selected. The liquid was sealed at a metal nozzle and then impacted using a polyethylene projectile. Applying laser cutting and copper-wire breaking methods, the jet and impact velocities were measured simultaneously. The results were analyzed by least squares method. From the obtained relationships between the jet and impact velocities, the threshold impact velocities for getting supersonic liquid jets were determined. A strobe light was used to visualize the injection sequence. In addition to the experiments, a theoretical analysis for the mechanism of generating the multiple liquid jets indicates that the exit hole number of a nozzle does not influence the injection velocity so much because of the three dimensional nozzle geometry and the small hole diameter.


Articles with similar content:

GEOMETRICAL EFFECTS ON DISCHARGE COEFFICIENTS FOR PLAIN-ORIFICE ATOMIZERS
Atomization and Sprays, Vol.1, 1991, issue 2
Arthur H. Lefebvre, Dwight W. Senser, T. R. Ohrn
GEOMETRIC EFFECTS ON SPRAY CONE ANGLE FOR PLAIN-ORIFICE ATOMIZERS
Atomization and Sprays, Vol.1, 1991, issue 3
Arthur H. Lefebvre, Dwight W. Senser, T. R. Ohrn
EFFECTS OF CAVITATION AND INTERNAL FLOW ON ATOMIZATION OF A LIQUID JET
Atomization and Sprays, Vol.8, 1998, issue 2
Keiya Nishida, Hiroyuki Hiroyasu, N. Tamaki, M. Shimizu
Geometric Primary Atomization Characteristics in an Airblast Atomizer, High Pressure Conditions
Atomization and Sprays, Vol.21, 2011, issue 1
P. Berthoumieu, G. Lavergne, Vital Gutierrez Fernandez
MEASUREMENT OF BREAKUP LENGTH OF CYLINDRICAL LIQUID JETS. APPLICATION TO LOW-PRESSURE CAR INJECTOR
Atomization and Sprays, Vol.11, 2001, issue 3
Christophe Dumouchel