Abo Bibliothek: Guest
Digitales Portal Digitale Bibliothek eBooks Zeitschriften Referenzen und Berichte Forschungssammlungen
Journal of Porous Media
Impact-faktor: 1.752 5-jähriger Impact-Faktor: 1.487 SJR: 0.43 SNIP: 0.762 CiteScore™: 2.3

ISSN Druckformat: 1091-028X
ISSN Online: 1934-0508

Volumes:
Volumen 24, 2021 Volumen 23, 2020 Volumen 22, 2019 Volumen 21, 2018 Volumen 20, 2017 Volumen 19, 2016 Volumen 18, 2015 Volumen 17, 2014 Volumen 16, 2013 Volumen 15, 2012 Volumen 14, 2011 Volumen 13, 2010 Volumen 12, 2009 Volumen 11, 2008 Volumen 10, 2007 Volumen 9, 2006 Volumen 8, 2005 Volumen 7, 2004 Volumen 6, 2003 Volumen 5, 2002 Volumen 4, 2001 Volumen 3, 2000 Volumen 2, 1999 Volumen 1, 1998

Journal of Porous Media

DOI: 10.1615/JPorMedia.v11.i7.20
pages 633-646

Superheated Steam Drying of a Spherical Porous Particle

Jalila Sghaier
Département d'Energétique, Ecole Nationale d'Ingénieurs de Monastir, Avenue Ibn Eljazzar, 5019 Monastir, Tunisie
Wahbi Jomaa
Laboratoire TREFLE-UMR 8508, Site ENSAM, Esplanade des Arts et Métiers, 33405 Talence Cedex, France
Ali Belghith
Faculte des Sciences de Tunis, Laboratoire des Transferts de Chaleur et de Masse, Campus Universitaire, 1060 Tunis, Tunisia

ABSTRAKT

In this article, we present a mathematical model to describe the drying kinetics occurring in a porous particle during superheated steam drying. This model is based on the averaging volume approach. It takes into account the effect of gradients of moisture content, temperature, and pressure. The heat flux by convection is given by the external transfer coefficient between the particle and the surrounding steam. The radiation exchange between the particle and the surrounding during the drying process in superheated steam vapor has been included. For the mass transfer, the natural physical condition at the drying surface is based on the equality of the partial pressure of the vapor and the external pressure of the stream. An iterative method is proposed to process this condition. The system of equations describing heat and mass transfer in a porous particle is solved numerically by the finite volume method with an irregular mesh. The predicted results from the model are compared with experimental data reported in the literature. The validated model is then used to investigate, parametrically the effects of system variables on the drying behavior of a porous particle in steam.


Articles with similar content:

Modeling Heat and Mass Transfer during Superheated Steam Drying of a Fixed Bed of Porous Particles
Journal of Porous Media, Vol.12, 2009, issue 7
Souad Messai, Jalila Sghaier, Ali Belghith, Wahbi Jomaa
WATER VAPOUR DIFFUSION AND THERMAL CONDUCTIVITY OF WET POROUS MEDIA
International Heat Transfer Conference 9, Vol.5, 1990, issue
Christian Moyne , Alain Degiovanni
COMPUTER SIMULATION OF SIMULTANEOUS HEAT AND MASS TRANSFER IN AGGREGATIVE FLUIDIZED BEDS
Transport Phenomena in Thermal Engineering. Volume 2, Vol.0, 1993, issue
M.R. Rahimpour, Dariush Mowla
Transport and Deposition of Fine Mode Particles in Porous Filters
Journal of Porous Media, Vol.9, 2006, issue 8
Antonio Ferreira Miguel, A. Heitor Reis
HEAT−MASS TRANSFER AND THEIR COUPLING EFFECTS IN SUBLIMATION PROCESS
International Heat Transfer Conference 10, Vol.9, 1994, issue
M. H. Shi, Weiping Yu , M. Feng